Marantz SC-7S2 Guide de l'utilisateur télécharger pdf (Page 17)

ENGLISH

REAR PANEL

PUSH

z bvc n , .mx

NAME AND FUNTION

z Input Balanced terminal

This terminal is to connect the components which have

balanced outputs i.e. CD Player.

When Bi-Amping, terminal B can not be used.

Balanced terminal → p5

x Input CD, Line 1, Line 2, Recorder (Unbal-

anced) terminal

This terminal is to connect the unbalanced terminals of

components., i.e. CD etc.

When Bi-Amping, terminal B can not be used.

c Rec out terminal

The terminal connects to the Input of Recording equip-

ment i.e. CD Recorders, Tape Recorder etc.

When Bi-Amping, the signal being input to channel A, will

be output to both A & B channels.

v Pre out Unbalanced 1,2 terminal

This connects to the un balanced inputs of a Power Amp.

When Bi-Amping, the signal being input to channel A, will

be output to both A & B channels.

b Pre out Balanced terminal

This terminal is connected to the Balanced input of the

Power Amplifier. When Bi-Amping, the signal being input

to channel A, will be output to both A & B channels.

n F.C.B.S. In/Out terminal

These terminals are for connecting one or more SC-7S2s

to each other. The IN is for receiving control signals. The

OUT is for sending Control signals.

m ID No. switch

Whilst several SC-7S2 are connected, to set up respective

ID No. to distinguish each products.

When only 1 unit is used, the No. will be set 1. Initial set-

ting is <1>.

This switch is to give ID numbers to each SC-7S2, when

two or more are used. When using only 1, SC-7S2 the ID

switch is set to 1. Factory setting is 1.

Trim adjustment in case of several units of SC-7S2 → p18

If using 2 or more SC-7S2s, you can use the trim Adjust-

ment.

See page 18.

, Mode switch

The switch to change Stereo mode and Bi-Amp mode.

Initial setting is <stereo>.

• In case SC-7S2 is used for normal 2 channel.

Setting <Stereo> mode.

• In case of complete Bi-Amp connection with 2 units of

SC-7S2.

Setting <Bi-Amp> mode.

In case of <Bi-Amp> mode, the signal input from A

channel will be out to both of A/B channels through Pre-

out terminal and Rec out terminal.

Then, input terminal on B channel can not be used.

This switch is to switch between Stereo & Bi-Amp Mode.

Factory setting is Stereo. Stereo is used for using only 1

SC-7S2. If using 2 or more SC-7S2s, you will set the switch

to Bi-Amp Mode. When Bi-Amping, the signal being input

to channel A, will be outputted to both A & B channels

through the Pre-out & REC out terminals. The B input ter-

minal can not be used in Bi-Amp Mode.

. AC IN socket

Connect to a household power outlet with supplied AC

CORD.

SC-7S2 UN DFU 01 ENG 3/3 06.8.9, 1:52 PMPage 13 Adobe PageMaker 6.5J/PPC

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 25 26

Commentaires sur ces manuels

Pas de commentaire

Marantz SC-7S2 Guide de l'utilisateur Page 17

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio Marantz SC-7S2