Marantz PD6140D Manuel d'utilisateur

Model PD6140D User GuidePlasma Monitor

3Rear View/ Terminal BoardA AC INConnect the included power cord here.B EXT SPEAKER L and RConnect speakers (optional) here. Maintain the correctpolar

4→ VIDEO1 → VIDEO2 → VIDEO3RGB/PC DVD/HDVIDEOPOSITION / CONTROLMENU/ENTERPOINTERZOOMOFF TIMEREXITVOLUMEMUTEWIDE DISPLAYMULTI SELECTAUTO ADJUSTID SELEC

5Battery Installation and ReplacementInsert the 2 “AAA” batteries, making sure to set them inwith the proper polarity.1.Press and open the cover.2.Ali

6POWER/STANDBYApprox.7m/23ft Using the wired remote control modeConnect the remote cable* to the remote control’s remotejack and the “REMOTE IN” termi

7InstallationVIDEO(IN/OUT)VIDEO 1VIDEO 2VIDEO 3AUDIO 1DVD1 / HD1R(MONO)LY Cb/Pb Cr/PrRGB2 / DVD2 / HD2RGB 1R/VDG/ B/HD(IN/ OUT)DVI (Digital RGB)AUDI

8Connecting Your PC or Macintosh ComputerConnecting your PC or Macintosh computer to your plasmamonitor will enable you to display your computer’s scr

95 4 3 2 115 14 13 12 1110 9 8 7 6Pin Assignments and Signal Levelsfor 15 pin RGB (Analog)Pin Configuration and Signal of theRGB 3 Connector (DVI Conn

10Note:1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT.When LOOP OUT is ON, do not connect an OUTPUT signal from another unit,

11Basic OperationsPOWERTo turn the unit ON and OFF:1. Plug the power cord into an active AC power outlet.2. Press the Power button (on the unit).The m

12OFF TIMERTo set the off timer:The off timer can be set to turn the power off after 30, 60,90 or 120 minutes.1. Press the OFF TIMER button to start t

Introduction to the Plasma MonitorMarantz’s Plasma Monitor is a seamless blend of cutting-edge visual technology and sophisticated design. At each inc

13Wide Screen Operation (manual)With this function, you can select one of six screen sizes.When viewing videos or digital video discs1. Press the WIDE

14FULL size screenThe image is expanded in the horizontal and verticaldirection.ZOOM size screenWhen wide signals are input.TRUEThe image is true reso

15Menu OperationsThe OSM window is displayed with respect to thescreen as shown on the diagram.* Depending on the screen’s mode, the OSM may bedisplay

16Main menu Sub menu Sub menu 2 Sub menu 3 Sub menu 4 RESETREFERENCEPICTURE CONTRAST ←→ YES 18BRIGHTNESS ←→ YES 18SHARPNESS ←→ YES 18COLOR ←→

17*1 Only when AUTO PICTURE is OFF*2 RGB/PC only*3 The default value is PC for model PD4220V.*4 The default value is LOW for model PD4220V.Mai

18Picture Settings MenuAdjusting the pictureThe contrast, brightness, sharpness, color and tint can beadjusted as desired.Example: Adjusting the contr

19Reducing noise in the pictureUse these settings if the picture has noise due to poorreception or when playing video tapes on which the picturequalit

20Changing the Gamma CurveThis feature adjusts the brightness of the midtone areaswhile keeping shadows and highlights unchanged.Example: Setting “3”S

21Adjusting the colorsUse this procedure to adjust hue and color density for red,green, blue, yellow, magenta and cyan.You can accentuate the green co

22Setting the allocation of the audio connectorsSetting the AUDIO 1, 2, and 3 connectors to the desiredinput.Example: Setting “AUDIO INPUT1” to “VIDEO

PrecautionsPlease read this manual carefully before using your plasmamonitor and keep the manual handy for future reference. CAUTIONRISK OF ELEC

23Option1 Settings MenuSetting the on-screen menuThis sets the position of the menu, the display format(horizontal or vertical) etc.Example: Turning t

24Setting the BNC connectorsSelect whether to set the input of the 5 BNC connectors toRGB and component.Example: Set the BNC INPUT mode to “COMP.”1. O

25Setting high definition images to the suitablescreen sizeUse this procedure to set whether the number of verticallines of the input high definition

26Resetting to the default valuesUse these operations to restore all the settings (PICTURE,AUDIO, IMAGE ADJUST, OPTION1~3, etc) to thefactory default

27PowermanagementmodeOnOffTurning the pictureback onPicture already on.Operate the keyboard ormouse. The picturereappears.POWER/STANDBYindicatorGreenR

28ORBITERUse this to set the picture shift.Example: Setting “ORBITER” to “AUTO1”Perform Steps 1-2 of LONG LIFE, then...3. Use the ▲ and ▼ buttons to s

29Setting the time for INVERSE/WHITESet a time duration.Example: Setting to that the INVERSE mode startsin 2 hours and proceeds for one hour and a hal

30Information䡵 Setting the timeWORKING TIME ...Set the time duration for “SCREENWIPER”.When the WORKING TIME is setto “ON” the mode will stay on.WAI

31Setting the picture size for RGB input signalsUse this procedure to switch the setting to “ON” or “OFF”.Example: Setting the “PICTURE SIZE” mode to“

32Option3 Settings MenuUsing the timerThis function sets the monitor to turn ON/OFFautomatically at a set time.Set “ADVANCED OSM” to “ON” in the main

To avoid damage and prolong operating life:1. Use only with 120V 50/60Hz AC power supply.Continued operation at line voltages greater than 120 VoltsAC

33FUNCTION ... Set the LONG LIFE function.䡵 To reset the programAlign the cursor with the DATE field that you wish toreset, then press the C

34Information䡵 PWR. ON MODE settingsLAST ...Last mode (the mode that was lastselected at the time the power wasswitched off).VIDEO1, 2, 3

35Loop Out settingWhen this feature is set to ON, the received signal will belooped out.Example: Setting “ON”Set “ADVANCED OSM” to “ON” in the main me

36Video Wall settingUse this feature to configure a 2×2 or 3×3 video wall.Set “ADVANCED OSM” to “ON” in the main menu (1/2), then perform the followin

37AUTO IDThis feature automatically sets the ID numbers of multipledisplays connected to each other.Example: Setting “ON”Set the ID number for the No.

38P. ON DELAY (Power on delay)Use this function to activate power-on delay.Turn on the AUTO ID before the following operations.Example: Setting “ON”Pe

39REPEAT TIMERUse this to set two timers. Each timer can use theDIVIDER, SOURCE and WORK TIME functions.Turn on the AUTO ID and set the DIVIDER (at 1,

40Color System Settings MenuSetting the video signal formatUse these operations to set the color systems of compositevideo signals or Y/C input signal

41External ControlApplicationThese specifications cover the communications control ofthe plasma monitor by external equipment.ConnectionsConnections a

42Remedy• If there are no abnormalities in the imageand sound, the noise is caused by thecabinet reacting to changes in humidity. Thiswill not affect

PrécautionsVeuillez lire avec attention ce manuel avant d’utiliser lemoniteur à plasma et le conserver accessible pour s’y référerultérieurement.

43*1 Overheat protectorIf the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, t

Model PD6140D InformationPlasma Monitor

2IMPORTANT SAFETY INSTRUCTIONS (PD6140D)Read before operating equipment1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. F

31. Lire ces instructions.2. Garder ces instructions.3. Respecter tous les avertissements.4. Suivre toutes les instructions.5. Ne pas utiliser cet app

4WarningNot for use in a computer room as defined in the Standardfor the Protection of Electronic Computer/ Data ProcessingEquipment ANSI/NFPA 75.This

5AvertissementNe pas utiliser dans une salle d’ordinateurs telle que définiedans la Norme pour la protection des ordinateursélectroniques/appareils de

6SpecificationsScreen Size 53.2"(H)⳯29.9"(V) inches1351(H)⳯760(V) mmdiagonal 61"Aspect Ratio 16 : 9Resolution 1365(H)⳯768(V) pixelsPixe

7Table of Signals Supported Screen modeSupported resolution• When the screen mode is NORMAL, each signal is converted to a 1024 dots⳯768 lines signal

8Printed on recycled paperPrinted in Japan39AW8510107S900051DECLARATION OF CONFORMITYThis device complies with Part 15 of FCC Rules. Operation is subj

Pour éviter des dommages et prolonger la durée deservice de l’appareil:1. N’utiliser qu’une source d’alimentation de 120 V 50/60 Hz CA. Le fait d’util

Printed in Japan 02/2004 ECMar 38AW8510227S900057 is a registered trademark.www.marantz.comYou can find your nearest authorized distributor or dealer

How to Attach Options to the Plasma Monitor ... 1Ventilation Requirements for enclosure mounting ... 1How to use the safety metal fittings and

150mm (2")50mm (2") 50mm (2")WallWall50mm (2")50mm (2")You can attach your optional mounts or stand to the plasma monitor in

2q PowerTurns the monitor’s power on and off.w Remote sensor windowReceives the signals from the remote control.e POWER/STANDBY indicatorWhen the powe