Marantz SA-11S1 Guide de l'utilisateur télécharger pdf (Page 17)

ENGLISH

CHANGING THE TEXT BRIGHTNESS ON

THE LCD (LCD CONTRAST ADJUSTMENT)

Changing procedure (Changes can be made from

the main unit when operation is stopped.)

q If playback is in progress, press the

STOP

button to stop playback.

w Hold down the

PAUSE

button on the main unit

for at least two seconds. (This operation does not

work on the remote control.)

After holding down the button for two seconds,

the current contrast value is displayed. Within two

seconds while it is displayed, press the

button to increase the contrast, or press the

button to reduce the contrast. Changes

can be made to the contrast level over the entire

range (+8 to -8).

If the or button is not pressed

within two seconds, the contrast is automatically

set to the currently displayed level.

Display example: Contrast +-0

e Pressing the

STOP

button while changing the

setting returns to the default setting (+-0).

* Any changes made to the LCD contrast setting

are retained even when the power is turned off.

TURNING OFF THE DISPLAY AND

ILLUMINATION (DISPLAY OPERATION)

This function is used to turn the LCD and illumination

lamps (blue) on and off. (Two display statuses are

available.)

1. Mode where LCD and illumination lamp (blue) turn

Each time the

DISPLAY

button is pressed during

playback, the LCD and illumination lamp (blue)

switch on and off.

When Display Off is set, the Display Off indicator

(red) lights up.

* When any related button is pressed (such as

when the

OPEN/CLOSE

button,

STOP

button, or button is used), the display is

automatically turned on, but the Display Off

indicator (red) remains lit. If a track is started in

this state, the display is automatically turned off

two seconds later.

* When a track is stopped, the Display Off

indicator (red) and illumination lamp (blue) light

up alternately.

2. Setting for turning on only LCD (illumination lamp

(blue) remains off)

In the default state, the illumination lamp (blue) is

lit. In this state, the illumination lamp (blue)

remains off regardless of whether the LCD is

turned on or off.

Changing procedure (Changes can be made

when operation is stopped.)

q If playback is in progress, press the

STOP

button to stop playback. To make the setting, hold

down the

DISPLAY

button for at least two

seconds from the remote control (RC-11SAS1).

w If the illumination lamp (blue) is lit, it is turned off

and is set off. To change the setting from off to

on, hold down the same operation

DISPLAY

button for at least two seconds to turn on.

* The illumination lamp (blue) off setting is retained

even when the power is turned off, and this setting

remains until the setting is changed to the on

setting.

* The LCD display on/off setting is not retained when

the power is turned off. (This enables you to enjoy

operation each time you use it.)

TIMER PLAY

This unit can perform timer play by cooperating with

your audio timer.

Connect this unit’s power cord to the audio timer’s

power socket and the timer’s power cord to power

outlet.

* For connection to audio timer and it’s operation,

please refer to the instruction manual of your audio

timer.

Setting method of Timer Play

q Press POWER switch to turn ON the power.

w Insert the disc to be played.

* In timer play mode, tracks are played normally.

e Set the audio timer.

Audio Timer

ABOUT BALANCED JACKS

q The balanced output connector uses a XLR

connector.

w The XLR connector for professional use is

internally wired in either of the following two

systems.

1. USA system (Pin w = COLD, Pin e = HOT)

GND

HOT

COLD

European system (Pin w = HOT, Pin e = COLD)

GND

COLD

HOT

e The SA-11S1 uses the 1. USA system.

When a preamp or main amplifier adopting the

European system is connected using a cable with

XLR balanced connectors, the reproduced signal

may be inverted of phase.

In this case, correct the wiring of the one of the

XLR connectors on the extremities of the cable

to the USA system by exchanging the connections

of pins w and e. This will make it possible to

play the signal with the correct phase.

SA-11S1N(ENG) 04.8.3, 4:42 AMPage 13 Adobe PageMaker 6.5J/PPC

1 2 ... 12 13 14 15 16 17 18 19

Commentaires sur ces manuels

Pas de commentaire

Marantz SA-11S1 Guide de l'utilisateur Page 17

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de CD Marantz SA-11S1