Marantz DR2100 Guide de l'utilisateur télécharger pdf (Page 10)

ENGLISH

EXPLANATION OF THE REAR

PANEL TERMINALS

CONNECTORS AND CONTROLS ON THE

MAIN UNIT

q Terminal for FM antenna, 75 ohms

For connecting an external FM antenna with a coaxial cable, or for

connecting a cable network.

w Terminals for AM antenna and

Grounding

To connect the supplied AM loop antenna, use the terminals marked

“AM” and “GND”.

In areas where the AM loop antenna gives unsatisfactory results, it is

recommended that the receiver be connected to an outdoor antenna.

Use the terminal marked ‘AM’ for this. A grounding lead can be connected

to the terminal marked ‘GND’ to further reduce interference. In this case,

it must be connected together with the supplied loop antenna.

e DVD input jacks

Connect to the audio/video output jacks of the DVD player (DV2100).

When the DV2100 is connected with the SYSTEM bus connection, the

SURROUND L/R, CENTER, and SUBWOOFER jacks should be

connected to these DVD input jacks. The FRONT L/R jacks should be

connected to the SYSTEM OUT jacks y.

r LD/VCD input jacks

Connect to the audio/video output jacks of the LD/VCD player.

t TV input jacks

Connect to the audio/video output jacks of the TV set.

y AUX input jacks (SYSTEM OUT jacks)

Connect to the audio/video output jacks of other equipment.

Connect to the SYSTEM AUDIO IN jacks of the Marantz AV system

(DR2100, DV2100) when the SYSTEM bus connection is used.

u VCR input/output jacks

Connect the IN jack to the audio/video output jack of your main VCR and

connect the OUT jack to the audio/video input jack of the VCR.

i MONITOR OUT jack

Connect to the video input jack of your TV.

o 6ch output jacks

These jacks are supplied for pre-amplifier output signals, and are used

to connect to external power amplifiers. (If necessary)

!0 SPEAKER SYSTEM terminals

Connect the front L/R, center, surround L/R speaker leads, observing

the + and - polarity of the leads and terminals.

!1 REMOTE CONTROL jacks

Connect to a component equipped with remote control jacks. (Refer to

page 3.)

!2 System control switch

This switch selects the system operation mode. Set to SYSTEM position

when the unit is being used in combination with a CD-R (DR2100) or

DVD (DV2100). If your component is not capable of system connection,

set this switch to INT position.

!3 AC inlet

Connect the provided power cord, and after all connections are finished,

connect the AC plug to a house hold outlet (AC 230V).

FRONT PANEL

A STANDBY/power button and indicator

Press to turn power ON and press again to switch to STANDBY mode.

The indicator lights GREEN when power is ON, and lights RED when in

STANDBY mode. The indicator lights AMBER when the timer program is

set during STANDBY mode.

B Infrared sensor

The infrared signal from the remote control unit enters the unit through

this window. To operate the unit with the receiver door open, point the

remote control infrared signal transmitter toward this window.

C PHONES jack

This jack is used to connect dynamic type headphones, which provide a

wide range sound. When the headphones are connected to this jack, the

speaker sound is turned off, and output sound is changed to stereo mode.

Note:

If the headphones are connected to this jack, the receiver door

does not close even if you press the door CLOSE button or the unit

is in standby mode.

The DV2100’s 5.1ch mode is changed to 2ch (STEREO) mode

automatically.

D SURROUND button

Press to change surround mode. The mode changes as follows.

When in DVD mode: STEREO → 5.1CH → CS Movie →

CS Music → STEREO

When in other mode: STEREO → CS Movie → CS Music → STEREO

Note:

Surround mode does not change while listening to AM broadcasts.

Press this button to cancel the AM beat noise while receiving the

AM broadcasts.

E TUNER button

Press to select FM or AM tuner when another source is selected and

select the JOG operation for TUNER selection. Use this button to select

the JOG operation for a scan of frequency, preset memory or RDS mode.

The TUNER button changes modes as below.

FREQUENCY mode: To scan tuning by frequency by JOG control.

PRESET mode: To scan tunings in the preset memory by JOG

control.

RDS mode: To select RDS control (PTY, TP, TA, and EON

SEEK) by JOG control.

Please refer to page 10 for tuner operations.

F BAND button

Press to change the reception band to FM or MW.

G MEMORY button

Press to set the preset memory of the tuner, clock time or timer program.

Please refer to the tuner and timer operations.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 23 24

Commentaires sur ces manuels

Pas de commentaire

Marantz DR2100 Guide de l'utilisateur Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel d'enregistrement Marantz DR2100