Marantz SR6001 Manuel d'utilisateur télécharger pdf (Page 54)

ENGLISH

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source

selected for listening through the SR6001 is sent to

the record outputs.

This means that any program you are watching

or listening to may be recorded simply by placing

machines connected to the outputs for TAPE OUT,

CD/CDR OUT and VCR OUT in the record mode.

To record the input source signal you are currently

watching or listening to

TUNING

PRESET

REMOTE CONTROLLER

RC5001SR

AMP

AUX2

BASS

TREBLE

AUDI O

ANGLE

SUB TITLE

DISC+

CH-SEL

V-O FF

ATT.

AUX1

MDMD

CDRCDR

CDCD

DVDDVD VCRVCR

TUNERTUNER

DSSDSS

TVTV

TAPE

STANDBY

PHONES

INPUT SELECTOR

AV SURROUND RECEIVER SR6001

PURE DIRECT HT-EQ

7.1CH INPUT

MODE AUTO

MULTI

PURE DIRECT

SURROUND

SPEAK

MULTI

DSD

POWER ON/OFF

DISP MULTI AUTO TUNED

SLEEP

SURR DIRECT

AUTO

Select the input source to record by turning the

INPUT FUNCTION SELECTOR knob on the

front panel or simply press the input selector

buttons on the remote.

The input source is now selected and you may

watch or listen to it as desired.

The currently selected input source signal is

output to the TAPE OUT, CD/CDR OUT and

VCR OUT outputs for recording.

Start recording to the recording component as

desired.

SPEAKER A/B

DIGITAL

VIDEO

S-VIDEO

AUX 1 INPUT

VOLUME

DOWN

MultEQ

ENTER

7.1CH INPUT

MULTI

A/B

T-MODE

MEMORY CLEAR

DISPLAY

EXIT

SPEAKERS

BAND

MIC

SPEAKER

MULTI

SL S SR

LFE

DIGITAL

SURROUND

V-OFF

LTI AUTO TUNED ST SPKR A B

NIGHT

PEAK ANALOG

DIGITAL

ATT

SURR DIRECT

AUTO

DISC 6.1 MTX 6.1 EQ

PCM

AAC

CAT

SCAN

CAT

789

+10+10

HT-EQ

MULTI/

SPKR A/B

ENTER

INFO

CH/

M-SPKR

MUTE

VOLUME

7.1CH IN

STEREO

NIGHT

MEMO

A/DA/D

SR6001 has speaker system - A and speaker

system- B for front L/R channels.

You can select these systems by pressing

SPEAKERS A/B button on the front panel or SPKR

A/B on the remote.

SELECTING ANALOG AUDIO INPUT OR

DIGITAL AUDIO INPUT

TAPE

REMOTE CONTROLLER

RC5001SR

CDR

DVD

AUX2

TUNER

AUX1

AMPAMP

CAT

P.SCAN

CAT

456

789

+10+10

HT-EQ

MULTI/

SPKR A/B

CH/

M-SPKR

MUTE

VOLUME

7.1CH IN

STEREO

NIGHT

M-CH ST

MEMO

A/DA/D

If you have already assigned the digital inputs, you

can temporarily select the audio input mode for each

input source as following procedures.

Press the AMP button ﬁ rst to enter the AMP mode

then press the A/D button.

When this button is pressed, the input mode is

switched in the following sequence.

Auto → HDMI → Digital → Analog → Auto

Auto mode:

The types of signals being input to the digital and

analog input jacks for the selected input source are

detected automatically.

If no digital signal is being input, the analog input

jacks are selected automatically.

HDMI mode:

HDMI mode can be selected only when an HDMI

input has been assigned as an input source.

When “HDMI AUDIO” under PREFERENCE of the

SETUP MENU is set to “THROUGH”, the HDMI

mode cannot be selected.

Digital mode:

The input signal is ﬁ xed to an assigned digital input

terminal.

Analog mode:

The analog input jacks are selected.

This selection is temporary and will not be stored in

memory.

To store changes to the input mode, select “1. INPUT

SETUP” from the MAIN MENU. (See page 28)

DISPLAY MODE

P.SCAN

T.MODE

123

456

789

SEND

INPUT

EX/ES

VIRTUAL

dts

P.DIRECT

OFF

SET

STEREO

NIGHT

M-CH ST

AUTO

SURROUND

SLEEP

LEARN

LIP SYNC/

SOURCE

DISPLAYDISPLAY

BAND

PHONES

AV SURROUND RECEIVER SR6001

MultEQ

ENTER

PURE DIRECT HT-EQ

7.1CH INPUT

MODE AUTO

MULTI T-MODE

MEMORY

DISPLAY

EXIT

BAND

MIC

PURE DIRECT

SURROUND

SPEAKER

MULTI

DSD

SL S SR

LFE

DIGITAL

SURROUND

V-OFFDISP MULTI AU TO TUNED ST SPKR A B

NIGHT

PEAK ANALOG

DIGITAL

ATT

SLEEP

SURR DIRECT

AUTO

DISC 6.1 MTX 6.1 EQ

PCM

AAC

You can select the display mode for the front display

of the SR6001.

To select this mode, press the DISPLAY on the

remote control or the front panel.

When this button is pressed, the display mode is

switched in the following sequence.

Input Mode → Surround Mode → Auto display OFF

→ Display OFF → Normal Mode → Input Mode

Normal Mode:

Displays the selected input function. If the function

has been renamed using the Function Rename

feature (see page 29), the renamed name appears

on the display.

Input Mode:

Displays the input mode set via the Function Input

Setup feature (see page 28).

Surround Mode:

Displays the status of the selected surround

mode.

Auto Display Off mode:

The display is off. But, if you make a change to

the unit such as the input or surround mode, the

display will show that change, then go back to off

after about 3 seconds. When changing the volume,

it is not displayed.

Display Off mode:

The display is off completely.

Note:

• Only the DISP indicator will be illuminated on the

front display in display off condition.

SR6001N DFU_1_ENG 3_4.indd 50SR6001N DFU_1_ENG 3_4.indd 50 06.12.21 3:11:45 PM06.12.21 3:11:45 PM

1 2 ... 49 50 51 52 53 54 55 56 57 58 59 ... 67 68

Commentaires sur ces manuels

Pas de commentaire

Marantz SR6001 Manuel d'utilisateur Page 54

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs et amplificateurs Marantz SR6001