Marantz DR2100 Guide de l'utilisateur télécharger pdf (Page 18)

ENGLISH

TIMER

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

MULTI JOGMULTI JOG

(PUSH ENTER)

MULTI JOG

(PUSH ENTER)

MULTI JOG

PROGRAMME TIMER SETTING

The timer function is built into this receiver allows you to perform the

following operations:

• Three timer settings at the same time: Program-1, Program-2 and

Program-3;

• Setting of ON time and OFF time;

• Setting of source: The source can be selected from tuner preset

number 1 to 50, DVD, AUX and AUTO;

• It is possible to specify the track numbers of DVD;

• It is possible to select recording or playing media;

• Setting of single operation (ONCE) or everyday operation (DAILY).

IMPORTANT:

The timer setting with track number specified can be used only

when the system control switch is set to SYSTEM position except

with using the tuner.

In the following procedure, each button should be pressed within 5

seconds after pressing the previous button.

When the remote control is used to set the timer, press the AMP

button v to change the AMP function mode at first.

1. Press the power button A/ z to turn the power of the unit ON.

2. Press the TIMER button K/⁄0. The display indicates “TMR

PROG”.

3. [SET THE ON TIME]

3-1. After a few seconds, “PROG-1” appears and starts blinking.

Turn the JOG control M or press the cursor

button n to

select the desired timer program, and press the ENTER button

M/ n. (If the selected program was used before, the details of

the previous setting appear.)

3-2. The display indicates “ON TIME” in the upper segment of the

display, and the present time is displayed in the middle

segment. (In this case, the present time is 10:05.)

3-3. “10” blinks. Turn the JOG control M or press the cursor

button n to adjust the hour. To increase, turn to the right. To

decrease, turn to the left. For example, set the hour to 12. (In

this case, AM changes to PM.)

3-4. Press the ENTER button M/ n to set the hour, and the minutes

start to blink.

3-5. “05” blinks. Turn the JOG control M or press the cursor

button n to adjust the minutes. For example, set the minutes to

30. (12:30)

3-6. Press the ENTER button M/ n to set the minutes and all

segments start to blink. When all segments blink, the time can be

re-adjusted using the JOG control M or press the cursor

button n.

3-7. Press the ENTER button M/ n to complete ON time setting.

The display stops blinking.

4. [SET THE OFF TIME]

4-1. “OFF TIME” then appears in the upper segment of the display,

and the time set as ON time (12:30) appears in the middle

segment.

4-2. “12” blinks. Turn the JOG control M or press the cursor

button n to adjust the time of timer stop. For example, “1”.

4-3. Press the ENTER button M/ n to set the time, and the minutes

start to blink.

4-4. Turn the JOG control M or press the cursor

button n to

adjust the minute of timer stop, and press the ENTER button M/

n to set the minute.

4-5. All segments blink in the display. The time can be re-adjusted

by turning the JOG control M or press the cursor

button n.

4-6. Press the ENTER button M/ n to complete the OFF time setting.

5. [SET THE MANUAL or AUTO] (only in SYSTEM mode)

5-1. The display indicates “AUTO” in the middle segment.

Note:

If “AUTO” is selected, the auto play function is activated, and it

detects the source that can be played. For example, if a disk is set

to CD side of DV2100, and no other player is set, the PS2100 will

play the CD in DV2100 automatically.

5-2. If you want to play a specified source in AUTO mode, you have

to set it.

5-3. If you want to select a source, you should select “MANUAL”.

6. [SET TO MANUAL]

6-1. Turn the JOG control M or press the cursor

button n to select

“MANUAL” and press the ENTER button M/ n. The display

indicates “MANUAL” for 2 seconds.

6-2. The display indicates the source name, for example DVD. Turn

the JOG control M or press the cursor

button n to select the

source and press the ENTER button M/ n.

At this time, you need to select the track number of the playing

medium. The display indicates “NUMBER XX”.

6-3. Turn the JOG control M or press the cursor

button n to

select the track number. To increase the number, turn the JOG

control M or press the cursor

button n to the right, and to

decrease, turn to the left. You can select number from 1 to 99.

Please confirm the desired track number of the selected

medium.

6-4. Press the ENTER button M/ n to set the track number to be

played. Next, select whether to record or not.

7. [SET TO “AUTO”]: This is available only when system control

switch is set to SYSTEM position

7-1. Turn the JOG control M or press the cursor

button n to

select “AUTO” and press the ENTER button M/ n. The display

indicates “AUTO” for 2 seconds. Next, set volume level.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 24

Commentaires sur ces manuels

Pas de commentaire

Marantz DR2100 Guide de l'utilisateur Page 18

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel d'enregistrement Marantz DR2100